Great-plains Disk Harrow Field Update Wing Hinge Manuel d'utilisateur télécharger pdf

Great Plains Mfg., Inc. Installation Instructions

1/27/2009 SeriesI 3323DH-4336DH Wing Hinge Update 557-331M

Disk Harrow Field Update

Wing Hinge

Applies to Models: Update Kit Numbers:

• 3323-4336 556-196V Bolt, Lock Nut & Washers

General Information

These instructions explain how to install

the Wing Hinge Update Kit.

Manual Update

Refer to the Disk Harrow operator’s

manual for detailed information on safely

operating, maintaining as it is very important to

grease wing hinges. Refer to parts manual for

part identification.

556-100M Operator’s Manual

556-100P Parts Manual

Before You Start

For safety it is best to park machine on

level concrete floor. Leave machine hooked to

tractor or some kind of hydraulic source so you

can raise machine up and down while you are

assembling Kit. Review these instructions and

make sure you understand where and how the

components are installed, and which existing

parts are removed or reused.

Tools Required

 Basic Hand Tools

Assembly Instructions

Refer to drawing on page 2.

Start by unfolding the wings and

removing transport lock from lift cylinders

and lower the machine to the ground. Note:

Replace bolts and washers one hinge at a

time. You should not slide the wing gang bar

away from center gang bar.

This is a list of the part numbers in

556-196V update kit that are used on wings

and leveler assembly.

Part No. Description

802-822C HHCS 1 1/2-6X13 GR5 SPTHD PLT

803-350C NUT HEX NYLOCK 1 1/2-6 PLT

804-236C WASHER HARD 1/4 X 3 OD

802-877C HHCS 1-8X9 GR8 SPTHD PLT

803-038C NUT HEX 1-8 NYLON INSERT PL

Remove the 1 1/2 nylock nut (1) off

the 1 1/2 x 13 hex bolt (2) and remove bolt

from the first hinge. Be sure to remove the

two 1 1/2 flat washers from one side of the

spool and wing gang tube. Note: The old 1

1/2 washers are installed to the rear of the

spool on the 3323-3329 and to the front of

the spool on the 4330-4336 models. You will

discard the old 1 1/2 hex bolt (1), nut (2) and

washer (3).

You are now ready to re-assemble this

hinge. Start by sliding the two new 1 1/2

washers (4), one on the front side of spool and

one on the rear of the spool. You may have to

hold the washers in place while you insert the

1 1/2 x 13 special thread hex bolt (5) through

the hinge assembly. Bolt must be installed so

the head of the bolt is in the bolt stop as

shown on page 2. Install the 1 1/2 nylock nut

(6), draw nut down snug but do not torque to

specs on this bolt as the hinge needs to move

freely.

You may now install the bolts and

washers one at a time on the other 3 hinges,

like you did on the first hinge assembly.

1 2 3

Disk Harrow Field Update 1

Résumé du contenu

Page 1 - Disk Harrow Field Update

Great Plains Mfg., Inc. Installation Instructions 1/27/2009 SeriesI 3323DH-4336DH Wing Hinge Update 557-331M 1 Disk Harrow Field Update Wi

Page 2

Installation Instructions Great Plains Mfg., Inc. SeriesI 3323DH-4336DH Wing Hinge Update 557-331M 1/27/2009 2 After you get the four hin

Page 3

Great Plains Manufacturing, Inc. Corporate Office: PO. Box 5060 Salina, Kansas 67402-5060 USA

Commentaires sur ces manuels

Pas de commentaire

Great-plains Disk Harrow Field Update Wing Hinge Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Great-plains Disk Harrow Field Update Wing Hinge. Great Plains Disk Harrow Field Update Wing Hinge User Manual [es] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Great-plains Disk Harrow Field Update Wing Hinge