Great-plains YP4025A-3215 32-Row 15-Inch Quick Start Manuel d'utilisateur Page 5

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 5
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 4
Quick Setup Guide for IntelliAg Model YP40 30” Twin Row Air Pro
11001-1542-200909
©2009 DICKEY-john Corporation
Speci cations subject to change without notice.
System Component Installation
Locate and install system components as shown in the diagram.
Note how the modules are identi ed and which modules are
located on which sections in this system.
Connect WSMB module harnesses together with included exten-
sions. Modules connect to the WSMT harness connection. Plug all
unused connectors with included dust plugs.
Secure any excess wires with tie-wraps.
See Operator’s Manual for additional installation information.
Power on monitor and program with correct constants as described
on this Quick Start Guide.
1.
2.
3.
4.
5.
5
467980846
Extension
Harness 25’
WSMB Module
Harness
467981201A
WSMB
Module
Seed Monitor
467981100S1
467980143
Extension
Harness 25’
WSMT
Module
Harness
467980151
Connect to
Actuator
Harness
467980160
Standard Dj SE Style
Planter Harness
Middle Section
467981701
Rows 11-22
467980143
Extension
Harness 25’
Standard Dj SE Style
Planter Harness
Left Section
467981720
Rows 1-10
Can
Terminator
Connect Cab Harness
to Implement Can
Harness
Radar Speed Sensor
467833000S1
(Radar connected to either
tractor harness or WSMT
as shown below)
Virtual
Te rm i na l
Chassis
Ground
CAN
Terminator
467980126
Ignition
Connect to
switched +12VDC.
NOTE: This wire
must be connected to
switched +12VDC
Master
Switch
(467980124S1)
+
-
Tractor Cab Harness
467980455
Battery
CFM
Tractor ECU
Controller
(467985060S1)
Harness
467980452
(5” Terminal) or
Harness
467980451A
(10” Terminal)
467984220S1
Tractor Harness
RS232
GPS
(467980451 Harness)
Implement CAN
Breakaway Harness
467980134
Connect to Optional
Hydraulic Tongue Harness
or to Extension
Hopper
Level
Sensors
467983502
467982000S1
Hydraulic
Tongue
Option
Connect to
Harness 467980134
Connect to
467980144
Extension
Note: Connect the WSMT
Actuator Harness and the
Dj Planter Harness to the
mating connectors of the
WSMT Module Harness
Connect to Harness
467980134 or
Hydraulic Tongue Option
467980410
Harness
Planter
Output
Module
464820517
Output 2 Hitch B1
Output 2 Hitch B2
Output 1 Lift
467980144
Extension
Harness
467980361
Rear Hitch
Harness
467980136
Extension
Harness
Pump Clutch
464820518S1
4667980470 Extension
Planter
Output
Module
467983503
467982000S1
Fertilizer Pump
Option
Boom 3 and
Bypass 467980430
Output 1
(Not Used)
Output 2
Boom 1 and 2
467980430
Can
Terminator
Output 1 Left Clutch
467980471 Extension
464820517S1
Output 1 Marker
Output 2 Fold
Planter
Output
Module
464820511S1
467983504
467982000S1
Clutch
Control
Output 2 Center Clutch
467980471 Extension
Right
Clutch
Output 1
464820518S1
467980473 Extension
Output 2
to Fold
Lock Valve
WSMT II
467980815S1
CFM
Harness
467980330
WSMB
Module
WSMB
Module
Harness
467981201A
Seed Monitor
467981100S1
Standard Dj SE Style
Planter Harness
Right Section
467981720
Rows 23-32
Accessory Sensors
connection to WSMT
ACTUATOR HARNESS
467980160
Application
Rate Sensor
(Channel 1-4 Feedback)
Labeled FB1-FB4
Hopper
Level Sensor
466820720S3
Implement Lift Sensor
464820520S1
If no implement lift
sensor is used, connect
the IMP LIFT leads
together
Fan/Shaft
RPM Sensor
466970014S1
Radar Speed Sensor
46783300S1
(Radar connected to
either tractor harness
or WSMT as shown below)
Servo Valves
(Labeled Servo 1 and Servo 2)
Actuator Harness
467980160
Test Switch
Implement
Lift Extension
Harness
466820713
Actuator
467096050
10’ Harness
457901815
Adapter
467980172
PWM Solenoid Valves
466820832S1
Pressure
Sensor
467980496
5’ Harness
457901826
Hopper Extension
Harness
466820714
Fan
Extension
Harness
459680922
Vue de la page 4
1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire