Great-plains YP4025A-3215 32-Row 15-Inch Quick Start Manuel d'utilisateur télécharger pdf (Page 4)

Quick Setup Guide for IntelliAg Model YP40 30” Twin Row Air Pro

11001-1542-200909

Speciﬁ cations subject to change without notice.

STEP 12: 5 Revolution Test

Press the Control Setup button .

Press the Channel Setup button .

Press the Next Page button .

Ensure implement is raised before starting 5 Rev Test.

With brakes locked and transmission in PARK position, start tractor engine.

Engage hydraulics and run engine at normal speed until hydraulic ﬂ uid is at operating

temperature.

Press the 5 Rev button .

Test Ground Speed and Row data must be entered to perform test.

Press and hold remote test button to initiate 5 Rev Test.

STEP 14: Summary Screen

The Summary screen provides an overview of setup constants for active control channels.

At the Main Work screen, press the Next Page button .

Press the Summary button

To view speciﬁ c control channel conﬁ gurations, press the respective control channel box

1-4.

Press inside a yellow highlighted box to open a speciﬁ c screen for editing.

Press the Work Screen button to return to the Main Work screen.

Summary

Screen

STEP 11: Clutch Folding Module Operation

The planter section controls turn the left, center, and right clutch controls on and off.

The master switch must be in the ON position to activate any planter section. When a clutch

control is ON, a green light will illuminate.

Marker/Fold Switch should be in the UP (Marker) position during planting. In the DOWN

(Fold) position, the switch controls the fold of the main frame.

The fertilizer pump switch is turned ON when in the UP position. Press the switch in the

DOWN position to turn OFF.

Lift/Hitch switch should be in the UP (Lift) position during normal operation. In the hitch posi-

tion, the switch should be in the DOWN (Hitch) position to unlock and extend the telescoping

tongue in preparation of folding the implement for transport.

Lift/Hitch switch MUST be in the hitch position and hydraulic circuit in FLOAT when trans-

porting planter equipped with hydraulic-operated tongue hitch. NOTE: Lift/Hitch switch has

no function if planter has standard 3-point hitch operated tongue hitch.

MASTER

Left Center Right Marker Fert. Pump Lift

MASTERMASTER

CLUTCH

Fold Hitch

Master

CFM Switch

Marker

Fold

Fertilizer

Pump

On/Off

Lift

Hitch

TABLE F:

Accessory

Setup

Default Value

or Value to

Enter

Instructions/Deﬁ nitions

Hopper Setup

# of Hoppers 1 (base unit)

1 more (optional)

# of hopper sensors connected to each module

(4 sensors maximum). # of hopper data items for

each listed module and the Hopp #’s value will auto-

matically populate if Auto Conﬁ g is used to conﬁ gure

installed sensors.

Logic Level Active Lo Sets the active state to low signifying that an alarm

is generated if the sensor’s output is in a low state.

Use this setting if the connected sensor outputs a

low condition when empty similar to the DICKEY-john

hopper sensor.

Alarm Delay 5 sec Controls the delay time between the detection of a

high/low hopper alarm condition and the generation of

the resulting alarm. The value is entered in seconds.

Channel Assigns hopper sensor to channel.

RPM Setup

High Alarm

(fan speed)

3000 rpm Sets the RPM value at which a high RPM warning

error is generated.

Low Alarm

(fan speed)

1800 rpm Sets the RPM value at which a low RPM warning error

is generated.

High Alarm Delay 10 sec Establishes the delay between the detection of a high

RPM alarm condition and the resulting alarm display.

The value is entered in seconds.

Low Alarm Delay 10 sec Establishes the delay between the detection of a low

RPM alarm condition and the resulting alarm display.

The value is entered in seconds.

RPM Constant 3 pulses/rev Number of pulses per sensor revolution.

RPM Filter 0 Filters the signal out of the RPM sensor.

Disable Control

on Low Alarm

Disabled Allows for disabling of all control channels if the RPM

value of the selected sensor falls below the low alarm

level setting.

STEP 9: Accessory Sensor Setup

Hopper Assignment

At the Main Work screen, press the Next Page button

Press the Module Conﬁ guration button to display the Module Conﬁ guration screen.

At the Module Conﬁ guration screen, press the Hopper Assign button .

Press Hopper Set button .

Enter desired values using Table F as reference.

RPM Assignment

At the Module Conﬁ guration screen, press the Acc Assign button .

Press the RPM Setup button .

Enter # of RPMs, if required. NOTE: There must be at least 1 RPM sensor conﬁ gured

before the RPM Setup button appears on the screen.

Enter desired values using Table F as reference.

STEP 10: Clutch Folding Module (CFM) Setup

The CFM is installed in the cab to control row clutches, marker, fold, fertilizer on/off, lift and

hitch.

At the Main Work screen, press the Clutch CFG button to access the Clutch Conﬁ guration

screen and verify that the correct # of clutches are conﬁ gured for the system.

The Clutch CFG button only appears as a top level button when a planter output

module and clutch folding module are installed.

OUTPUT

1-10

# OF

ROWS

ROW

#’s

11-22

23-32

LEFT

CENTER

RIGHT

# of Clutches

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Great-plains YP4025A-3215 32-Row 15-Inch Quick Start Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Great-plains YP4025A-3215 32-Row 15-Inch Quick Start