Great-plains YP1225A-16TR36 16 Twin Row 30-Inch Quick Start Manuel d'utilisateur télécharger pdf (Page 2)

Quick Setup Guide for IntelliAg Model YP1225 36” Twin Row Air Pro

11001-1593-201108

Speciﬁ cations subject to change without notice.

TABLE C1:

Planter Control

Setup

Default Value/

Value to Enter Instructions/Deﬁ nitions

Type Planter Control Set desired Channel Type as Planter Control.

Material Name Displays only materials that have been conﬁ gured for the channel

type.

Control Mode AUTO Auto is used in normal operating conditions calculating the rate of how

the system is running. Manual mode acts as an override if application

rate sensors are inoperable allowing the use of increase/decrease

buttons to set the ﬂ ow rate for the control. Refer to System Conﬁ gura-

tion section of Operator’s manual for additional information.

Drive Type PWM A hydraulic valve varies the oil ﬂ ow to the motor proportioned to the

electric current supplied.

Drive Frequency 100 Hz If not using a DICKEY-john supplied valve, see the manufacturer’s

speciﬁ cations for drive frequency.

Input Filter 50 Feedback frequency ﬁ lter for the control channel. DO NOT CHANGE.

Gear Ratio 1.900 Specifys the actual ratio from the feedback sensor to the seed meter

shaft RPM. Number of revolutions the feedback sensor turns in rela-

tion to one revolution the seed meter turns.

Sensor Constant 360 Sensor Constant establishes the number of pulses for one revolution

of the feedback sensor. If a DICKEY-john application rate sensor is

used, the value should be set to 360.0.

# of Seed Rows 16 Entry of a speciﬁ c number of seed rows for the control channel.

Row assignment is given a priority based on the channel and will be

assigned sequentially thereafter. Channel 1 is always assigned to the

ﬁ rst set of rows, Channel 2 next set of rows, and so on.

Channel Width

288 Manual entry of the channel width for rows assigned to a speciﬁ c

channel. Width calculation can be determined by # of planter rows

assigned to the channel multipled by the row spacing.

Precharge Time + 0.0 Typically used during startup conditions in the ﬁ eld, a Precharge

time is a speciﬁ ed length of time a control channel will operate at the

deﬁ ned Precharge Ground Speed. Must be entered as a positive (+)

number.

Delay Time - 0.0 Length of time before the control channel will start after the master

switch has been turned ON and the implement switch is in a lowered

position. Must be entered as a negative (-) number.

STEP 6A: Planter Control Channel Setup

(Controlled Hydraulic Drive)

Select Channel 1 and verify that the channel is set to Planter Control.

Enter desired values using Table C1 as reference.

After planter control setup, calibrate hydraulic valve by pressing the Valve Cal

button .

Ensure implement is raised. With brakes locked and transmission in PARK

position, start engine.

Engage hydraulics and run engine at normal speed until hydraulic ﬂ uid is at

operating temperature.

Verify point row clutches are turned ON.

Do NOT perform this step unless meters are installed in all locations

across planter row units or drive damage will occur.

Press the START button . Turn the master switch to the ON position.

The valve calibration will immediately start. Keep the hydraulics engaged until

the calibration completes.

When the screen indicates calibration is complete, press the Channel Setup

button to return to Channel 1 home screen.

Turn the master switch OFF.

To set up additional control channels (planter or fertilizer control), press the

Next Channel button .

Press the Work Screen button when channel conﬁ gurations are com-

plete to return to the Main Work screen.

Once a control channel has been established as Planter Control, any new materi-

als established as Planter Control on the Material Setup screen will automatically

be added as optional materials for Planter Control channels on the Control Setup

screen.

10.

11.

12.

TABLE B2:

Material Setup

Default Value/

Value to Enter

Ground Driven Metering

Instructions/Deﬁ nitions

Type Monitor Only Desired type of application control channel being used for a speciﬁ c

material.

Units Ks/Ac

S/Sec

Automatically changes with the type of material application selected.

Changes units for target application.

Target Population 32.0 1000s of seeds per acre or hectare (32,000 seeds per acre)

High Pop Alarm Warns of a high population problem. Values are % based.

Low Pop Alarm Warns of a low population problem. Values are % based.

On/Off Pattern Rows can be automatically turned ON or OFF according to the

pattern.

Row Fail Rate 2/1 (2 seeds

every 1 second)

Set to desired number of seeds per second to trigger seed sensor

failure alarm.

STEP 5B: Material Conﬁ guration Setup (Ground Drive Metering)

For Ground Drive Metering, control channels 1, 3, and 4 MUST be disabled

and the Monitor Only feature selected at the Control Setup screen. NOTE: A

Material Name must also be selected at the Row Monitor screen to activate

high and low population alarms.

At the Main Work screen, press the Next Page button

one time.

Press the Control Setup button .

Select and press one of the Material buttons (Material 1-16).

Enter desired values from Table B2.

Press the Control Setup button to return to the Control Setup screen.

Repeat steps 3-5 for additional materials.

Press the Channel Setup button to proceed to the Channel Setup

screen and disable any active channels (Step 6B).

STEP 6B: Planter Control Channel Setup

(Ground Driven Metering)

NOTE: When using a ground drive/nonhydraulic application to monitor

population, control channels 1, 3, and 4 must be disabled and Material Setup

conﬁ gured for Monitor Only. A material name must also be selected on the

Row Monitor screen.

Press the Channel Setup button .

Select Channel 1 and verify that the channel is set to Disabled.

Press the Next Channel button to change control channels 3 and 4 to

Disabled.

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Great-plains YP1225A-16TR36 16 Twin Row 30-Inch Quick Start Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Great-plains YP1225A-16TR36 16 Twin Row 30-Inch Quick Start