Great-plains YP2425A-48TR 48 Twin Row 30-Inch Quick Start Manuel d'utilisateur télécharger pdf (Page 2)

Quick Setup Guide for IntelliAg Model YP24 Twin Row Air Pro

11001-1518-200908

Speciﬁ cations subject to change without notice.

STEP 6A: Material Conﬁ guration Setup (Split Air Regulation)

It is recommended that when setting a control channel for split air, the material

name be created as “Air” to eliminate confusion between the actual material and

the control used.

At the Main Menu screen, press the Control Setup button

Press Material button 16 for Split Air Control.

Create Material Name as “Air”.

Enter desired values from Table C1.

Press the Channel Setup button to proceed to the Channel Setup screen.

TABLE C1:

Material Setup

Default Value/

Value to Enter

Split Air Regulation

Instructions/Deﬁ nitions

Type Split Air Reg Desired type of application control channel being used for a

speciﬁ c material. CREATE MATERIAL NAME AS “AIR”.

Units In H

Oz in

Automatically changes with the type of material application

selected. Changes units for target application.

Preset Method Disabled User-deﬁ ned target rates can be conﬁ gured and when enabled

can be adjusted from the Main Work screen using the Incre-

ment/Decrement buttons.

Target Rate 2.00 Establishes the desired rate of application in inches of H

Max Rate 5.00 Maximum application rate in inches of H

Min Rate 1.00 Minimum application rate in inches of H

Inc/Dec % 5% Percentage of change of the entered target rate applied each

time the Increment/Decrement button is pressed on the Main

Work screen.

STEP 5B: Planter Control Channel Setup

(Controlled Hydraulic Drive)

Select Channel 1 and verify that the channel is set to Planter Control.

Enter desired values using Table B2 as reference.

After planter control setup, calibrate hydraulic valve by pressing the Valve Cal

button .

Ensure implement is raised. With brakes locked and transmission in PARK posi-

tion, start engine.

Engage hydraulics and run engine at normal speed until hydraulic ﬂ uid is at

operating temperature.

Verify point row clutches are turned ON.

Do NOT perform this step unless meters are installed in all locations across

planter row units or drive damage will occur.

Press the START button . Turn the master switch to the ON position.

The valve calibration will immediately start. Keep the hydraulics engaged until the

calibration completes.

When the screen indicates calibration is complete, press the Channel Setup button

to return to Channel 1 home screen.

Turn the master switch OFF.

To set up additional control channels (planter or fertilizer control), press the Next

Channel button .

Press the Work Screen button when channel conﬁ gurations are complete

to return to the Main Work screen.

Once a control channel has been established as Planter Control, any new materials

established as Planter Control on the Material Setup screen will automatically be

added as optional materials for Planter Control channels on the Control Setup screen.

10.

11.

12.

TABLE B2:

Planter Control

Setup

Default Value/

Value to Enter Instructions/Deﬁ nitions

Type Planter Control Set desired Channel Type as Planter Control.

Material Name Displays only materials that have been conﬁ gured for the chan-

nel type.

Control Mode AUTO Auto is used in normal operating conditions calculating the rate

of how the system is running. Manual mode acts as an override

if application rate sensors are inoperable allowing the use of

increase/decrease buttons to set the ﬂ ow rate for the control.

Refer to System Conﬁ guration section of Operator’s manual for

additional information.

Drive Type PWM A hydraulic valve varies the oil ﬂ ow to the motor proportioned to

the electric current supplied.

Drive Frequency 100 Hz If not using a DICKEY-john supplied valve, see the manufactur-

er’s speciﬁ cations for drive frequency.

Input Filter 50 Feedback frequency ﬁ lter for the control channel. DO NOT

CHANGE.

Gear Ratio 1.900 Specifys the actual ratio from the feedback sensor to the seed

meter shaft RPM. Number of revolutions the feedback sensor

turns in relation to one revolution the seed meter turns.

Sensor Constant 360 Sensor Constant establishes the number of pulses for one

revolution of the feedback sensor. If a DICKEY-john application

rate sensor is used, the value should be set to 360.0.

# of Seed Rows 48 Entry of a speciﬁ c number of seed rows for the control channel.

Row assignment is given a priority based on the channel and

will be assigned sequentially thereafter. Channel 1 is always

assigned to the ﬁ rst set of rows, Channel 2 next set of rows, and

so on.

Channel Width

720 Manual entry of the channel width for rows assigned to a speciﬁ c

channel. Width calculation can be determined by # of planter

rows assigned to the channel multipled by the row spacing.

Precharge Time + 0.0 Typically used during startup conditions in the ﬁ eld, a Precharge

time is a speciﬁ ed length of time a control channel will operate

at the deﬁ ned Precharge Ground Speed. Must be entered as a

positive (+) number.

Delay Time - 0.0 Length of time before the control channel will start after the

master switch has been turned ON and the implement switch is

in a lowered position. Must be entered as a negative (-) number.

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Great-plains YP2425A-48TR 48 Twin Row 30-Inch Quick Start Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Great-plains YP2425A-48TR 48 Twin Row 30-Inch Quick Start