Great-plains YP1625-1670 16 Row 70 cm Quick Start Manuel d'utilisateur télécharger pdf (Page 3)

Quick Setup Guide for IntelliAg Model YP1625 70 cm

11001-1597-201108

Speciﬁ cations subject to change without notice.

STEP 7: Row Monitor Setup

At the Main Work screen, press the Row Monitor button .

Enter desired values using Table D as reference.

Press the Work Screen button

to return to the Main Work screen.

TABLE D:

Row Monitor

Setup

Default Value/

Value to Enter Instructions/Deﬁ nitions

Material Name See Instructions Material Name only appears on the Row Monitor Setup screen when all

control channels are disabled and material is set for Monitor Only. This is only

used for ground drive/nonhydraulic applications to monitor population with

high and low alarms. A material must be conﬁ gured and selected to activate

alarms.

High Alarm Delay 5 Desired number of seconds that high population can be above high alarm

point before alarm will sound.

Low Alarm Delay 5 Desired number of seconds that low population can be below low alarm point

before alarm will sound.

Population Adjust 100 Enter a % to allow for seed sensor population inaccuracies to achieve the

desired population display. 100% represents true calculation.

Population Filter 50 Set ﬁ lter value to stabilize the monitored population display. Number can be

set to 0% for no ﬁ ltering and 99% for high level ﬁ ltering.

Row Fail Rate 2/1 (2 seeds

every 1 second)

Set to desired number of seeds per second to trigger seed sensor failure

alarm.

TABLE E:

Speed Set Default Value/

Value to Enter Instructions/Deﬁ nitions

Source Digital Frequency Select CAN Ground if radar is connected to ISO tractor cab harness. Select

Digital Frequency if radar or hall-effect is connected to WSMT actuator har-

ness.

Gspd Constant 2546 Input based on pulse count produced by the ground speed sensor over 400’

distance. See Operator’s manual for calibration instructions.

Shutoff Speed 0.5 kph Set desired minimum ground speed allowed before the system shuts off.

Minimum

Override

2.0 kph Set to operate when actual ground speed falls below the designated value.

Control will operate at this speed until actual ground speed rises above mini-

mum override speed or actual speed drops below shutoff.

Master Sw

Timeout

10 Set to desired number of seconds system shuts off if the master switch is

turned on and there is no ground speed. Toggle master switch to restart the

system and turn off alarm.

Gspd Fail Alarm

Delay

5 Set to desired number of seconds alarm sounds after the ground speed is zero

and seed ﬂ ow continues. (Monitor only)

Precharge

Ground Speed

0 Set to the desired speed the system will use when a precharge time has been

enabled for a control channel. Refer to Table C1: Planter Control Setup for

Precharge Time. This setting will only display when a Precharge Time has

been entered.

Implement Lift Enabled Implement lift switch, when enabled, displays an implement lift indicator on

the Main Work screen indicating implement lift position as up or down. Control

channels can be turned on and off without using the master switch.

STEP 8: Speed Set Calibration Setup

At the Main Work screen, press the Speed Set button .

Enter desired values using Table E as reference.

Press the Work Screen button when ground speed calibration

conﬁ gurations are complete to return to the Main Work screen.

TABLE F:

Accessory

Setup

Default Value /

Value to Enter Instructions/Deﬁ nitions

Hopper Setup

# of Hoppers 1 (base unit)

1 more (optional)

# of hopper sensors connected to each module (4 sensors maximum). # of

hopper data items for each listed module and the Hopp #’s value will automati-

cally populate if Auto Conﬁ g is used to conﬁ gure installed sensors.

Logic Level Active Lo Sets the active state to low signifying that an alarm is generated if the sensor’s

output is in a low state. Use this setting if the connected sensor outputs a low

condition when empty similar to the DICKEY-john hopper sensor.

Alarm Delay 5 sec Controls the delay time between the detection of a high/low hopper alarm

condition and the generation of the resulting alarm. The value is entered in

seconds.

Channel Assigns hopper sensor to channel.

RPM Setup

High Alarm

(fan speed)

4200 rpm Sets the RPM value at which a high RPM warning error is generated.

Low Alarm

(fan speed)

2900 rpm Sets the RPM value at which a low RPM warning error is generated.

High Alarm Delay 10 sec Establishes the delay between the detection of a high RPM alarm condition

and the resulting alarm display. The value is entered in seconds.

Low Alarm Delay 10 sec Establishes the delay between the detection of a low RPM alarm condition

and the resulting alarm display. The value is entered in seconds.

RPM Constant 3 pulses/rev Number of pulses per sensor revolution.

RPM Filter 0 Filters the signal out of the RPM sensor.

Disable Control

on Low Alarm

Disabled Allows for disabling of all control channels if the RPM value of the selected

sensor falls below the low alarm level setting.

STEP 9: Accessory Sensor Setup

Hopper Assignment

At the Main Work screen, press the Next Page button .

Press the Module Conﬁ guration button to display the Module

Conﬁ guration screen.

At the Module Conﬁ guration screen, press the Hopper Assign button

Press Hopper Set button .

Enter desired values using Table F as reference.

RPM Assignment

At the Module Conﬁ guration screen, press the Accessory Assignment

button .

Press the RPM Setup button . NOTE: There must be at least 1

RPM sensor conﬁ gured before the RPM Setup button appears on the

screen.

Enter desired values using Table F as reference.

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Great-plains YP1625-1670 16 Row 70 cm Quick Start Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Great-plains YP1625-1670 16 Row 70 cm Quick Start