Great-plains YP3025A-3610 36-Row 10-Inch Quick Start Manuel d'utilisateur télécharger pdf (Page 2)

Quick Setup Guide for IntelliAg Model YP30 10” Air Pro

11001-1555-201009

Speciﬁ cations subject to change without notice.

TABLE B2:

Planter Control

Setup

Default Value/

Value to Enter Instructions/Deﬁ nitions

Type Planter Control Set desired Channel Type as Planter Control.

Material Name Displays only materials that have been conﬁ gured for the channel

type.

Control Mode AUTO Auto is used in normal operating conditions calculating the rate

of how the system is running. Manual mode acts as an override

if application rate sensors are inoperable allowing the use of

increase/decrease buttons to set the ﬂ ow rate for the control.

Refer to System Conﬁ guration section of Operator’s manual for

additional information.

Drive Type PWM A hydraulic valve varies the oil ﬂ ow to the motor proportioned to

the electric current supplied.

Drive Frequency 100 Hz If not using a DICKEY-john supplied valve, see the manufacturer’s

speciﬁ cations for drive frequency.

Input Filter 50 Feedback frequency ﬁ lter for the control channel. DO NOT

CHANGE.

Gear Ratio 1.900 Specifys the actual ratio from the feedback sensor to the seed

meter shaft RPM. Number of revolutions the feedback sensor

turns in relation to one revolution the seed meter turns.

Sensor Constant 360 Sensor Constant establishes the number of pulses for one revolu-

tion of the feedback sensor. If a DICKEY-john application rate

sensor is used, the value should be set to 360.0.

# of Seed Rows 36 Entry of a speciﬁ c number of seed rows for the control channel.

Row assignment is given a priority based on the channel and will

be assigned sequentially thereafter. Channel 1 is always assigned

to the ﬁ rst set of rows, Channel 2 next set of rows, and so on.

Channel Width

360 Manual entry of the channel width for rows assigned to a speciﬁ c

channel. Width calculation can be determined by # of planter rows

assigned to the channel multipled by the row spacing.

Precharge Time + 0.0 Typically used during startup conditions in the ﬁ eld, a Precharge

time is a speciﬁ ed length of time a control channel will operate

at the deﬁ ned Precharge Ground Speed. Must be entered as a

positive (+) number.

Delay Time - 0.0 Length of time before the control channel will start after the master

switch has been turned ON and the implement switch is in a

lowered position. Must be entered as a negative (-) number.

STEP 5B: Planter Control Channel Setup

(Controlled Hydraulic Drive)

Select Channel 1 and verify that the channel is set to Planter Control.

Enter desired values using Table B2 as reference.

After planter control setup, calibrate hydraulic valve by pressing the Valve Cal

button .

Ensure implement is raised. With brakes locked and transmission in PARK

position, start engine.

Engage hydraulics and run engine at normal speed until hydraulic ﬂ uid is at

operating temperature.

Verify point row clutches are turned ON.

Do NOT perform this step unless meters are installed in all locations

across planter row units or drive damage will occur.

Press the START button . Turn the master switch to the ON position.

The valve calibration will immediately start. Keep the hydraulics engaged until

the calibration completes.

When the screen indicates calibration is complete, press the Channel Setup

button to return to Channel 1 home screen.

Turn the master switch OFF.

To set up additional control channels (planter or fertilizer control), press the

Next Channel button .

Press the Work Screen button when channel conﬁ gurations are

complete to return to the Main Work screen.

Once a control channel has been established as Planter Control, any new materi-

als established as Planter Control on the Material Setup screen will automatically

be added as optional materials for Planter Control channels on the Control Setup

screen.

10.

11.

12.

STEP 6A: Material Conﬁ guration Setup (Split Air Regulation)

It is recommended that when setting a control channel for split air, the

material name be created as “Air” to eliminate confusion between the actual

material and the control used.

At the Main Work screen, press the Control Setup button .

Pressure Material button 16 for Split Air Control.

Create Material Name as “Air”.

Enter desired values from Table C1.

Press the Channel Setup button to proceed to the Channel Setup

screen.

TABLE C1:

Material Setup

Default Value/

Value to Enter

Split Air Regulation

Instructions/Deﬁ nitions

Type Split Air Reg Desired type of application control channel being used for a speciﬁ c

material. CREATE MATERIAL NAME AS “AIR”.

Units In H

Oz in

Automatically changes with the type of material application

selected. Changes units for target application.

Preset Method Disabled User-deﬁ ned target rates can be conﬁ gured and when enabled can

be adjusted from the Main Work screen using the Increment/Decre-

ment buttons.

Target Rate 2.00 Establishes the desired rate of application in inches of H

Max Rate 5.00 Maximum application rate in inches of H

Min Rate 1.00 Minimum application rate in inches of H

Inc/Dec % 5% Percentage of change of the entered target rate applied each time

the Increment/Decrement button is pressed on the Main Work

screen.

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Great-plains YP3025A-3610 36-Row 10-Inch Quick Start Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Great-plains YP3025A-3610 36-Row 10-Inch Quick Start