Great-plains 3S-4000HDF Predelivery Manual Manuel d'utilisateur

Manufacturing, Inc.www.greatplainsmfg.com© Copyright 2009 Printed 12/10/2009 195-067QPredelivery Manual3S-4000HDThree-Section Folding HD DrillRead the

8 3S-4000HD195-067Q 12/10/2009Install Walkboards and StepsThere are three walkboards, one on the back of eachseed box. The walkboards themselves are i

Assembly 912/10/2009 195-067QInstall Swing-Down LaddersIf the drill includes swing-down ladders, they are installedafter the walkboards are installed.

10 3S-4000HD195-067Q 12/10/2009Install Ladders1. Lay the ladder on the walkboard with the swingholes up and near the top mount lug holes . Alignthe h

Assembly 1112/10/2009 195-067QInstall Reflectors and DecalsTo prevent scuffing in shipment, walkboard decals areshipped in a bag in one of the drill box

12 3S-4000HD195-067Q 12/10/2009Swing-Down Ladder DecalsRefer to Figure 12Starting on the left wing walkboard:1. Place the 838-102C Danger Falling Haza

Assembly 1312/10/2009 195-067QTwo Outlet KitIf the Two-Outlet Hydraulic Kit was ordered, install it now(before the markers, as this kit contains items

14 3S-4000HD195-067Q 12/10/2009Open Center ConversionIf the drill was shipped with an Open Center kit, it is notfactory-installed. Install it now. An

Setup 1512/10/2009 195-067QSetupThe assembly steps of the preceding chapter must becompleted prior to setup.Setup steps consist of:1. Hitch to suitabl

16 3S-4000HD195-067Q 12/10/2009Hitch HeightRefer to Figure 19 and Figure 201. To adjust the drill hitch to match your tractor-drawbarheight, mount ton

Setup 1712/10/2009 195-067QRefer to Figure 215. Use crank to raise jack foot. Remove pin and jack.Store jack on top of tongue.Electrical ConnectionsIf

3S-4000HD195-067Q 12/10/2009Table of Contents© Copyright 2001, 2006, 2007. 2009 All rights Reserved.Great Plains Manufacturing, Inc. provides this pub

18 3S-4000HD195-067Q 12/10/2009Hydraulic Hose HookupOnly trained personnel should work on system hydraulics!Escaping fluid under pressure can have suffi

Setup 1912/10/2009 195-067QBleeding HydraulicsTo function properly, the hydraulics must be free of air. Ifhydraulics have not been bled, they will ope

20 3S-4000HD195-067Q 12/10/2009Bleeding Opener Lift HydraulicsRefer to Figure 241. Review warnings, bleeding notes and system infor-mation on page 19.

Setup 2112/10/2009 195-067QBleeding Fold HydraulicsRefer to Figure 251. Review warnings, bleeding notes and system infor-mation on page 19.2. With dri

22 3S-4000HD195-067Q 12/10/2009Bleeding Transport Lift HydraulicsRefer to Figure 261. Review warnings, bleeding notes and system infor-mation on page

Setup 2312/10/2009 195-067QBleeding Marker HydraulicsYou may be injured if hit by a folding or unfolding marker.Markers may fall quickly and unexpecte

24 3S-4000HD195-067Q 12/10/2009Leveling the DrillTo perform leveling, the drill must be hitched to a tractor,with at least the hydraulics connected.Ra

Setup 2512/10/2009 195-067QWing Box Alignment1. Place a block ahead of the wing gauge wheels.Refer to Figure 302. Pull forward against blocks to rock

26 3S-4000HD195-067Q 12/10/2009Align Transfer Drive ShaftRefer to Figure 32 and Figure 33After wing boxes are properly aligned, the transfer driveshaf

Setup 2712/10/2009 195-067QRefer to Figure 34 and Figure 353. To align the clutch jaws from front to rear, loosenthe two1⁄2inch carriage bolts and sl

112/10/2009 195-067QImportant Safety InformationFor your safety, thoroughly read Important Safety Infor-mation in the operator’s manuals before procee

28 3S-4000HD195-067Q 12/10/2009Truss Tube TensionThe truss tubes help hold the center tool bar perpendicu-lar to the tongue and straight under load. A

Setup 2912/10/2009 195-067QOpener-Frame ClearanceRefer to Figure 38When fully raised, top of opener mounts should clearbottom of drill frame tube by

30 3S-4000HD195-067Q 12/10/2009Shaft MonitorRefer to Figure 40If the drill was ordered with the optional shaft monitor,install the sensors and leads p

Appendix 3112/10/2009 195-067QAppendixSpecifications and Capacities 3S-4000HD-7806 3S-4000HD-6375 3S-4000HD-4810Row Count78 63 48Row Spacing6 in (15.

32 3S-4000HD195-067Q 12/10/2009Torque Values Chart25199BoltSizeBolt Head IdentificationBoltSizeBolt Head IdentificationGrade 2 Grade 5 Grade 8 Class 5.8

Appendix 3312/10/2009 195-067QHydraulic DiagramsTransport LiftFold1560215602

34 3S-4000HD195-067Q 12/10/2009Dual MarkersSingle Marker1560515605

Appendix 3512/10/2009 195-067QTwo Outlet Conversion15605

36 3S-4000HD195-067Q 12/10/2009Opener Lift: Standard Closed-Center22976

Appendix 3712/10/2009 195-067QOpener Lift: Optional Open-Center22977

2 3S-4000HD195-067Q 12/10/2009Transport Machinery SafelyMaximum transport speed for drill is 20 mph (32 kph).Some rough terrains require a slower spee

38 3S-4000HD195-067Q 12/10/2009Point-Row22969

Great Plains Manufacturing, Inc.Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USAEOD

312/10/2009 195-067QPractice Safe Maintenance▲ Understand procedure before doing work. Use proper toolsand equipment. Refer to this manual for additio

4 3S-4000HD195-067Q 12/10/2009IntroductionGreat Plains Manufacturing wants you to be satisfiedwith any new machine delivered by the Great PlainsTruckin

Introduction 512/10/2009 195-067QUsing This ManualThis manual was written to help you assemble and pre-pare the new machine for the customer. The manu

6 3S-4000HD195-067Q 12/10/2009PreparationStep-by-step instructions for assembling the implementbegin in the next section of the manual. Before commenc

Assembly 712/10/2009 195-067QAssemblyInstall Center Box on FrameRefer to Figure 31. Unload mainframe/wing assembly from truck andplace it in a locati