Great-plains YP2425A-4715 47 Row 15-Inch Quick Start Manuel d'utilisateur télécharger pdf

Quick Setup Guide for IntelliAg Model YP24 15” Air Pro

11001-1519-200908

Speciﬁ cations subject to change without notice.

STEP 1: Pre-Programming Preparation:

Power on vehicle via ignition switch to activate Virtual Terminal (VT). Main menu will display pre-programmed default settings.

If errors are detected (e.g., failed sensors, incorrect conﬁ guration) an alarm and code displays. Alarms are silenced by pressing the Alarm Cancel button

. Refer to Operator’s

manual for troubleshooting assistance.

The system has three user levels. The system loads in User Level 1 (operator level) at every power cycle. Access to User Level 2 and 3 screens to setup constants (system conﬁ gura-

tion) requires a password.

The Quick Setup Guide assumes the Virtual Terminal, Master Switch, Working Set Master Module, Working

Set Member Module, and all sensors have been connected and properly installed. Reference Operator’s

manual for installation instructions. NOTE: The master switch is only required for hydraulic control

systems. Reference the manual for instructions to assign a master switch as an auxiliary input.

STEP 3: Auto Conﬁ guration (Identiﬁ es sensors connected to each module)

Auto conﬁ g is performed at the factory, but may need to be done in the ﬁ eld as changes are

made to the system or if options are added to the base planter.

Verify Auto Conﬁ g results are correct. Check that the correct number of rows are assigned to the

correct module and number of hopper sensors are assigned accurately.

To Run Auto Conﬁ g:

Press the Next Page button until the Module Conﬁ guration button appears.

Press the Module Conﬁ guration button .

Press the AUTO CONFIG button .

Hour glass will indicate system is being conﬁ gured detecting the presence of seed or hopper

sensors connected to each module and will be automatically assigned to the appropriate

module.

When Auto Conﬁ g completes, press the Row Assign button to display the Row Assign-

ment screen to verify correct Row # is assigned to the correct module based on serial number.

Enter # of rows assigned to each module.

STEP 4: Row Status/Row Width Setup

At the Row Assignment screen, press the Row I/O button .

Begin entering desired values using Table A as reference.

Press the Work Screen button when Row Status/Row Width conﬁ gurations are

complete to return to the Main Work screen.

TABLE A: Row

Status/Row

Width Setup

Default Value

or Value to

Enter

Instructions/Deﬁ nitions

Row Width 15” Enter row width distance in inches to calculate seed

rate correctly. NOTE: Using 15” planter in 30” mode

should change On/Off Pattern to Every 2nd Row Off.

Auto Update Width Enabled When enabled, implement width will automatically cal-

culate. If disabled, manually enter implement width.

On/Off Pattern Every Row On On/Off Pattern indicates speciﬁ c row patterns to

be on or off. Select pre-deﬁ ned planter All Row On

pattern. For other pre-deﬁ ned planter patterns or

individual row settings, reference Operator’s manual.

Pop/Block Pattern Every Row

Population

Determines which sensors are used to calculate

population and those used only for blockage detec-

tion. Select pre-deﬁ ned Every Row Population. For

other pre-deﬁ ned patterns, reference Operator’s

manual.

STEP 2: Change User Level to Dealer Level

To change the user level, a 6-digit password is required. Password includes the ﬁ ve-digit

serial number found on the label of the Working Set Master or Information screen.

On the IntelliAg Main Work screen, press the Diagnostics button .

At the Diagnostics screen, press the Information button .

At the Information screen, record serial number of WSMT.

Press the Password button .

On the Password screen, enter the 6 digit password as follows: enter the ﬁ rst digit as 2 for User

Level 2. For the next ﬁ ve digits, enter the Working Set Master serial number taken from the

WSMT or Information screen.

Press the OK button . “Dealer screens on” appears at the bottom of screen conﬁ rming

the password and dealer screens are activated.

Press the Work Screen button to return to the Main Work screen.

STEP 5A: Material Conﬁ guration Setup (Controlled Hydraulic Drive)

15 different materials can be conﬁ gured for use as planter controls. Reference the System Con-

ﬁ guration section in the Operator’s manual for additional information.

At the Main Menu screen, press the Control Setup button .

Select and press one of the Material buttons (Material 1-15).

Enter desired values from Table B1.

Press the Control Setup button to return to the Control Setup screen.

Repeat steps 2-4 for additional materials.

Press the Channel Setup button to proceed to channel setup screen.

TABLE B1:

Material Setup

Default Value/

Value to Enter

Controlled Hydraulic Drive

Instructions/Deﬁ nitions

Matrl Label Matrl 1 Material Name can be customized to accurately

deﬁ ne the material’s type. Creating a name allows for

quick identiﬁ cation at the Control Setup screen.

Type Planter Control Desired type of application control channel being

used for a speciﬁ c material. The Material Type must

correctly match the Control Type to be able to select

Material from the Material Summary screen and

operate properly.

Units Ks/Ac

S/Sec

Automatically changes with the type of material appli-

cation selected. Changes units for target application.

Preset Method Enable Enabled Preset Method allows 10 user-deﬁ ned target

rates to be adjusted from the Main Work screen

using Inc or Dec buttons. A Disabled Preset Method

increases/decreases the target rate based on the %

values set at the Material Setup screen.

Seeds per Rev See Manual Set to number of seeds per 1 disc revolution.

Disc Low Limit

(Air Pro)

5 Set to desired min seed disc RPM.

Disc High Limit

(Air Pro)

37 Set to desired max seed disc RPM.

High Pop Alarm 15% This is the percentage above the target population of

the planter channel if rows are assigned to the planter

channel. If rows are not assigned to a planter, this is

the percentage above average planter population for

all unassigned rows.

Low Pop Alarm 15% This is the percentage below the target population

of the planter channel if rows are assigned to the

planter channel. If rows are not assigned to a planter

channel, this is the percentage below average planter

population for all unassigned rows.

Product Level

Alarm

Sets the level to trigger an alarm alerting of low prod-

uct levels. Entered value is an estimate in volume.

Row Fail Rate 2/1 (2 seeds

every 1 second)

Set to desired number of seeds per second to trigger

seed sensor failure alarm.

SERIAL

NUMBER

MODULE

TYPE

MODULE

ADDR.

WSMB-POM

WSMB-18R

10001

10002

WSMT-GY

WSMB-Rows

WSMB-POM

WSMB-CFM

10001

10002

10003

10001

# OF

ROWS

MODULE

ADDR.

TYPE

ROW

#’s

19-29

WSMB-18R

WSMT-GY

1- 18

WSMB-Rows

30-47

Module Configuration Screen Seed Sensor Configuration Screen

(optional)

1 2 3 4 5

Résumé du contenu

Page 1 - WSMB-Rows

Page 2

Page 3 - (Split Air Regulation)

Page 4 - # of Clutches

Page 5 - 467980160

Commentaires sur ces manuels

Pas de commentaire

Great-plains YP2425A-4715 47 Row 15-Inch Quick Start Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel de jardinage Great-plains YP2425A-4715 47 Row 15-Inch Quick Start. Great Plains YP2425A-4715 47 Row 15-Inch Quick Start User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Great-plains YP2425A-4715 47 Row 15-Inch Quick Start